Skip to main content

Solid Edge Productivity Summit Tour

Well, things in the Solid Edge world are certainly active these days, and Siemens PLM is being very serious about increasing user oppurtunities.  The first big evidence of this is that the folks at Siemens PLM responsible for the Solid Edge product are hosting 17 regional events around North America for users to attend for FREE!

The current agenda posted on Siemens site (http://img.en25.com/Web/Siemens/Solid%20Edge%20Productivity%20Summit%20agenda_6188a.pdf) looks like this:


 
Solid Edge Productivity Summit Preliminary Agenda – Times and sessions subject to change by location

  •  8 a.m. to 4 p.m.
  • Check in and registration
  • Solid Edge Vision and Direction
  • Solid Edge Customer Success Presentation
  • Modeling in Solid Edge with synchronous technology
  • Patterning in Solid Edge
  • Networking Lunch
  • Synchronous Sheet Metal Modeling
  • Best Practices in Solid Edge Drafting
  • Regional Tips and Tricks in Solid Edge
  • Synchronous Assembly Modeling
  • Using Both Traditional &and Synchronous
  • Tips and Tricks in Solid Edge
Sign-up here:
http://am.siemensplmevents.com/?elqPURLPage=3363

Locations and Dates are:
  • Orlando, FL - July 27, 2010
  • Kansas City, MO - July 28, 2010
  • Clearwater, FL - July 29, 2010
  • Atlanta, GA - August 10, 2010
  • Houston, TX - August 11, 2010
  • Dallas, TX - August 12, 2010
  • Cleveland, OH - August 12, 2010
  • Montreal, QC - August 17, 2010
  • Toronto, ON - August 18, 2010
  • Huntsville, AL - August 18, 2010
  • Indianapolis, IN - August 24, 2010
  • Cincinnati, OH - August 25, 2010
  • Boston, MA - August 26, 2010
  • Philadelphia, PA - August 31, 2010
  • Phoenix, AZ - September 8, 2010
  • Cypress, CA - September 9, 2010
  • Seattle, WA - September 10, 2010
 Ken

Comments

SolidMatters said…
Do you know if the summit held in Montreal will be in English? & who is hosting it? I'd like to attend this one because its the closest but I don't speak french. Thx
PellaKen said…
I have heard that it will be in English. Not sure who is hosting it.
Anonymous said…
Check with the local Siemens PLM office, they should know : 1-877-847-6567. Ask to speak to the local AE. Or the Designfusion guys (local VAR) should know too.

Popular posts from this blog

Solid Edge Replace Part Options

If you are not familiar with the Solid Edge Replace Part command, it is an Assembly based command used to do what the name implies… replace a part or sub-assembly with another part or sub-assembly. In past releases of Solid Edge, the Replace Part command was a solo act that had the ability of replacing a single part or sub-assembly occurrence or all occurrences of that selection with a user specified replacement part or sub-assembly that already existed. With the release of Solid Edge ST5 and subsequent releases, the Replace Part command was actually expanded into 4 different Replace Part commands, each with their own specific capabilities. Replace Part Replace Part is similar to the previous Replace Part command in that it is used to replace a part with one that has already been created, however it was expanded to allow not only the selection of a single occurrence or all occurrences of the selection, but also allows a user to select different parts and/or specified num...

Dimension Projection Line Breaks

Often when placing dimensions on drawings, the projection lines of some dimensions will cross the projection lines of other dimensions as shown below. Solid Edge provides a function to automatically create breaks in one extension line where it crosses another. This function is called "Add Projection Line Break". It is accessible from the Shortcut Menu when you have a dimension highlighted. The result is shown below. If you wish to remove the projection line break, highlight the dimension, invoke the shortcut menu, and select "Remove Projection Line Break".

Solid Edge ST7

Solid Edge ST7 is not due for release until July 2014, but it appears it is actively being worked on by SE Development as witnessed by a recent post from Dan Staples on the GTAC Solid Edge discussion group where he revealed a new enhancement by accident.  Whoops!  No worries, it was a simply a setting switch so he really didn't let much of the cat out of the bag (tip of a whisker?). The good news is that we have several more months till launch so he has plenty of time to reveal more about ST7, and knowing Dan, he might let a few teasers out just to keep things interesting. BETA should commence in early spring, and the official launch will occur at Solid Edge University 2014 in May.  No doubt Synchronous Technology based modeling will continue to be a focus, but it's anyone guess as to what the other areas of focus are...