Skip to main content

Synchronous Technology

So, on April 22nd, Siemens PLM Software released a bomb on the CAD world about a new modeling paradigm. There looks to be a lot of promise to this new technology, and I have high hopes for it.

One problem I regularly see today with the sketch/feature/history based modelers is that concept modeling and production modeling are at odds.

What I mean by this is:
  • An engineer while in the concept modeling phase is concerned about creating geometry to fill a needed form. They may make many variations of this model, some with minor differences and some with major differences. They do not care about building in design intent or making the model easy to modify, so they use what I term "hack and whack" modeling. What is left when they are done is a model with a feature tree that would put Frankenstein's monster to shame.
  • After the concept phase comes the documentation phase. This is where ease of modification and design intent is a concern. This usually results in a model being remodeled which is of course rework and is never desired.

This problem appears to be solved with Synchronous Technology. The concept model can be "hacked and whacked" into the needed form (with more ease promised) and when it is ready to become a production model, the user can simply apply the needed parameters to preserve the design intent (no remodeling needed). I see this as a huge time saver.

Another issue I regularly see with sketch/feature/history based modelers is that part-time users (a couple days a month) still have difficulty using them for design work due to all the historic and associative relationships to planes, sketches, and other features that the user must be constantly concerned with. If modeling could be made easier and more intuitive as the Synchronous Technology claims to be without reliance on those historic and associative relationships, that would be a huge benefit.

There will apparently be a Solid Edge launch on May 21st. I'm sure the CAD media will be buzzing then.

Labels

Labels:

Comments

Anonymous said…
People should read this.
November 11, 2008 at 2:33 AM
Post a Comment

Popular posts from this blog

Solid Edge Replace Part Options

If you are not familiar with the Solid Edge Replace Part command, it is an Assembly based command used to do what the name implies… replace a part or sub-assembly with another part or sub-assembly. In past releases of Solid Edge, the Replace Part command was a solo act that had the ability of replacing a single part or sub-assembly occurrence or all occurrences of that selection with a user specified replacement part or sub-assembly that already existed. With the release of Solid Edge ST5 and subsequent releases, the Replace Part command was actually expanded into 4 different Replace Part commands, each with their own specific capabilities. Replace Part Replace Part is similar to the previous Replace Part command in that it is used to replace a part with one that has already been created, however it was expanded to allow not only the selection of a single occurrence or all occurrences of the selection, but also allows a user to select different parts and/or specified num...
Post a Comment
Read more

Dimension Projection Line Breaks

Often when placing dimensions on drawings, the projection lines of some dimensions will cross the projection lines of other dimensions as shown below. Solid Edge provides a function to automatically create breaks in one extension line where it crosses another. This function is called "Add Projection Line Break". It is accessible from the Shortcut Menu when you have a dimension highlighted. The result is shown below. If you wish to remove the projection line break, highlight the dimension, invoke the shortcut menu, and select "Remove Projection Line Break".
1 comment
Read more

Solid Edge ST7

Solid Edge ST7 is not due for release until July 2014, but it appears it is actively being worked on by SE Development as witnessed by a recent post from Dan Staples on the GTAC Solid Edge discussion group where he revealed a new enhancement by accident.  Whoops!  No worries, it was a simply a setting switch so he really didn't let much of the cat out of the bag (tip of a whisker?). The good news is that we have several more months till launch so he has plenty of time to reveal more about ST7, and knowing Dan, he might let a few teasers out just to keep things interesting. BETA should commence in early spring, and the official launch will occur at Solid Edge University 2014 in May.  No doubt Synchronous Technology based modeling will continue to be a focus, but it's anyone guess as to what the other areas of focus are...
Post a Comment
Read more