Skip to main content

Solid Edge ST3 Impending Announcement on October 13th

Siemens PLM will formally announce Solid Edge ST3 on October 13th.  There are a number of events being held across North America starting on that day and through the month of December in a variety of cities.  2 of them are Siemens PLM hosted “National” events which the agenda shows will have a little more content in them, and the rest are Partner hosted events.  If interested in attending one of these events, you can sign up on the Register link at the following page: http://am.siemensplmevents.com/?elqPURLPage=4232
Now seeing that we have around 2-1/2 weeks before the formal announcement and there has been much speculation about what’s new with ST3 in regards to Synchronous Technology, I thought it would be interesting to invite your comments about what you think is new with Synchronous Technology in ST3.  Ground rules are that you must be polite and on topic.  This BLOG is mine and is not bound by your right to free speech, therefore comments are moderated and I reserve the right to reject any comments I perceive to violate the ground rules.
Now let the speculation begin!

Technorati Tags: ,,,,

Labels

Labels:

Comments

Anonymous said…
My guess is that Synchronous can be used in the traditional environment.

regards,
Theodore
September 27, 2010 at 10:41 AM
Anonymous said…
I hope there is a fusion between Sync and Tard modus.

I don't like the decition between Sync and Trad, there should be a fusion like NX.
September 28, 2010 at 4:30 AM
Anonymous said…
I am hoping that instead of 100X faster it is 100X better.

Probably it is that all the solids operations are now in synchronous and the only thing that is only traditional is surfacing.

I would be pleasantly surprised if the bridge was the ability to go back and for between traditional and ST like you can between sheetmetal and part.
September 28, 2010 at 6:34 AM
Post a Comment

Popular posts from this blog

Solid Edge Replace Part Options

If you are not familiar with the Solid Edge Replace Part command, it is an Assembly based command used to do what the name implies… replace a part or sub-assembly with another part or sub-assembly. In past releases of Solid Edge, the Replace Part command was a solo act that had the ability of replacing a single part or sub-assembly occurrence or all occurrences of that selection with a user specified replacement part or sub-assembly that already existed. With the release of Solid Edge ST5 and subsequent releases, the Replace Part command was actually expanded into 4 different Replace Part commands, each with their own specific capabilities. Replace Part Replace Part is similar to the previous Replace Part command in that it is used to replace a part with one that has already been created, however it was expanded to allow not only the selection of a single occurrence or all occurrences of the selection, but also allows a user to select different parts and/or specified num...
Post a Comment
Read more

Dimension Projection Line Breaks

Often when placing dimensions on drawings, the projection lines of some dimensions will cross the projection lines of other dimensions as shown below. Solid Edge provides a function to automatically create breaks in one extension line where it crosses another. This function is called "Add Projection Line Break". It is accessible from the Shortcut Menu when you have a dimension highlighted. The result is shown below. If you wish to remove the projection line break, highlight the dimension, invoke the shortcut menu, and select "Remove Projection Line Break".
1 comment
Read more

Solid Edge ST7

Solid Edge ST7 is not due for release until July 2014, but it appears it is actively being worked on by SE Development as witnessed by a recent post from Dan Staples on the GTAC Solid Edge discussion group where he revealed a new enhancement by accident.  Whoops!  No worries, it was a simply a setting switch so he really didn't let much of the cat out of the bag (tip of a whisker?). The good news is that we have several more months till launch so he has plenty of time to reveal more about ST7, and knowing Dan, he might let a few teasers out just to keep things interesting. BETA should commence in early spring, and the official launch will occur at Solid Edge University 2014 in May.  No doubt Synchronous Technology based modeling will continue to be a focus, but it's anyone guess as to what the other areas of focus are...
Post a Comment
Read more