Skip to main content

Solid Edge ST4 Launch Event (aka “The Solid Edge Summit”)

Six years ago, the last Solid Edge Summit was held in Cincinnati Ohio.  It was a wildly successful event.  The following year, someone made the decision to roll Solid Edge into the PLM World event and dissolve the Summit.  Needless to say it was a very bad decision as the attendance dwindled over the next 5 years to essentially a handful of  individuals which most likely happened due to a variety of reasons such as the poorly handled transition, higher cost for less value, a weakening economy, and a loss of the Solid Edge identity and community at an event that appeared to cater to NX/Teamcenter.

This year, the Solid Edge Summit was back!  Disguised as a Solid Edge ST4 Launch Event, it was essentially a 2 day user conference (June 15-16) held in Huntsville, Alabama which happens to be home of the Solid Edge Development office.  Needless to say, we as users have gotten to meet many of the development, certification, support, planning, marketing and the management team.  The agenda included a half day comprised of a business update, keynote presentation, and ST4 Introduction, followed by a day and a half of a 3 track agenda of presentations, hands on training and round table discussions.  The night before the event there was a welcome reception, and at the end of the first day, we all let our hair down at a social event held in a local arcade/bowling alley/bar & grill.

Besides the obvious training opportunity, one of the biggest advantages of going to these types of events is the building of “community”. At the Solid Edge ST4 Launch Event, that community was building fast.  Everywhere you looked, you would see Solid Edge folks.  Sit down at breakfast or lunch, and you were sitting with Solid Edge folks. At the social events, you were talking with Solid Edge folks.  A lot of folks knew each other from the newsgroup or phone calls/e-mails, but there is something about meeting folks face to face that cannot be duplicated any other way.

Everybody was very positive about this event and I’m certain they are already looking forward to next years event as much as I am.  For those who were not able to attend this event, I sure hope you can make the next one.

Comments

DougK said…
Ken,
It was good to meet you at the event. I agree with your summary of the event and hope they do it each year. Have you had a chance to try the new Web site we launched for the SE users at event with access to hundreds of manufacturers catalogs for free? Here's that URL if you forgot:
http://solidedge.partcommunity.com

We also created a guided tour to show you how it works:
http://www.youtube.com/watch?v=pecDifF57RY

I'd like to get your opinion; we are working on the second release already.

Doug Korneffel
Cadenas/PARTsolutions

Popular posts from this blog

Solid Edge Replace Part Options

If you are not familiar with the Solid Edge Replace Part command, it is an Assembly based command used to do what the name implies… replace a part or sub-assembly with another part or sub-assembly. In past releases of Solid Edge, the Replace Part command was a solo act that had the ability of replacing a single part or sub-assembly occurrence or all occurrences of that selection with a user specified replacement part or sub-assembly that already existed. With the release of Solid Edge ST5 and subsequent releases, the Replace Part command was actually expanded into 4 different Replace Part commands, each with their own specific capabilities. Replace Part Replace Part is similar to the previous Replace Part command in that it is used to replace a part with one that has already been created, however it was expanded to allow not only the selection of a single occurrence or all occurrences of the selection, but also allows a user to select different parts and/or specified num...

Dimension Projection Line Breaks

Often when placing dimensions on drawings, the projection lines of some dimensions will cross the projection lines of other dimensions as shown below. Solid Edge provides a function to automatically create breaks in one extension line where it crosses another. This function is called "Add Projection Line Break". It is accessible from the Shortcut Menu when you have a dimension highlighted. The result is shown below. If you wish to remove the projection line break, highlight the dimension, invoke the shortcut menu, and select "Remove Projection Line Break".

Solid Edge ST7

Solid Edge ST7 is not due for release until July 2014, but it appears it is actively being worked on by SE Development as witnessed by a recent post from Dan Staples on the GTAC Solid Edge discussion group where he revealed a new enhancement by accident.  Whoops!  No worries, it was a simply a setting switch so he really didn't let much of the cat out of the bag (tip of a whisker?). The good news is that we have several more months till launch so he has plenty of time to reveal more about ST7, and knowing Dan, he might let a few teasers out just to keep things interesting. BETA should commence in early spring, and the official launch will occur at Solid Edge University 2014 in May.  No doubt Synchronous Technology based modeling will continue to be a focus, but it's anyone guess as to what the other areas of focus are...